Jump to content

My Tutorial On The Project Red Transport Pipes!


Recommended Posts

If the screwdriver doesn't work. You can also make a cover and slip it In between the side you are trying to remove the connection from. I had to do that because I had a system already setup and a mod pack update caused all my pipes to rotate and connect to the incorrect inventory.

Link to post
Share on other sites

Using microblocks to solve the issue though then requires the use of a saw and blocks, using my method doesn't require a saw to be used let alone the use of additional blocks. But this method would work as well, especially in existing systems where there is a large amount of storage set-up already.

Link to post
Share on other sites

If the screwdriver doesn't work. You can also make a cover and slip it In between the side you are trying to remove the connection from. I had to do that because I had a system already setup and a mod pack update caused all my pipes to rotate and connect to the incorrect inventory.

I also use this quite a bit. My bases always seem to have fluiducts and itemducts going everywhere in the walls, so I use glass covers to make sure nothing connects.

Link to post
Share on other sites

some notes about the tutorial - the reinforced chests, lockers, and storage crates do indeed work with the pipes just fine. However keep in mind that the crates fail to broadcast all of the items available unless each crate has a broadcaster on it, this said it can store a ton of the same item and it seems to fill out when it can but it'll have residual items in it.

 

Looped pipes cause issues in any fashion (even if the loop is very large) and should always be avoided. Microblocks can be used in compact set-ups to avoid loops on machines.

 

Using the extraction orientation property on the chip, you can make a single pipe run on machines to make an input/output system wihtout the need of the additional pipe being ran for output - however this is set on a per machine basis for the side that is intended to be the output.

 

Using a hopper on a chest to extract items is too slow for the upgraded chips (even non-upgraded in some cases) to be effective and using the pipe directly on a chest is a better way to go as there won't be any delay caused by a hopper.  you can have a dual chest set-up next to each other (using reinforced chests or a trapped/normal chest) - this said, reinforced chests can be placed next to each other if they are the same type and not have them join together by placing the same type a block away (air gap between) then placing the non-connecting chest in-between that, then removing the unnecessary third chest.

 

 

the timer for stock keeper seems to be based on a 100 tick timer (like the other pipes & chips) however I'm entirely unsure if it uses 100 ticks initially then lowers itself until the stock is kept (similar to how MFR machines use the idle bar at a longer duration initially until it finds work then making it a lower delay between cycles)

 

 

For mob farms/grinders, using a tesseract set-up to send items into the system can prevent pipes from being needed to be ran directly to storage, however this will cause an issue with storage if it is not maintained and have a bunch of items flow into the system, this can be bypassed by using a buffer chest that if it fills up, to turn off the tesseract on that end, thus turning off the connection for the other (Sending only) tesseracts to accept input.

 

Junction pipes should really only be used at intersections, otherwise the regular pipes will be randomized each time and cause a long delay for items to be sent to the right direction, the junction pipes (along with the other pipes which act like junction pipes) is a lot smarter than you may think.

 

For the trash system, there is  a much more compact system available with regular redstone, and probably could be more compact with the use of ProjRed:Integration. I could describe this if you're interested and provide pictures.

 

 

I believe this covers all of the info i wanted to make note of from watching the video. Any questions/clarification on things, let me know.

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Content

    • By DoxNotch
      Hello again guys! DoxNotch back here with a more detailed and in-depth tutorial with the thermal expansion mod for the Attack of The B-Team modpack. This tutorial is supposed to teach you guys everything you need to know about setting up highly functional power systems, and how to use the power that you generate. I go over my favorite power system using magma crucibles and magmatic dynamos, and I teach you a few other designs as well. Reactant dynamos and Compression dynamos are going to be saved for a Minecraft Factory Reloaded tutorial later on, though. I hope you guys enjoy it and learn a lot! If you have any remaining questions about the mod, ask me in the comments!
    • By DoxNotch
      Hello again guys! Dox back here with a new tutorial! Today I'll be showing you guys how to make a full-auto dye farm using the Project Red dyed saplings, Minecraft Factory Reloaded Harvesters and Planters, and some Thermal Expansion stuff! I hope you guys enjoy it and just ask me if you have any questions. Remember to like/comment/subscribe if you dig!
×
×
  • Create New...